Frigidaire Appliance Repair in Valdosta, GA

Frigidaire appliance repair is the diagnosis and component replacement of refrigerators, washers, dryers, dishwashers and ranges built by Frigidaire, the mainstream North American badge of Electrolux. Frigidaire uses three separate code families rather than one: E-codes on washers, i-codes on dishwashers and F-codes on ranges. Each names the circuit that failed, which makes Frigidaire one of the faster brands to diagnose correctly over the phone.

Call 229-363-0182

Code families: E washers, i dishwashers, F ranges
Tiers covered: Frigidaire, Gallery, Professional
Parent company: Electrolux, since 1986
Availability: Open 24 hours

How does the Frigidaire fault code system work?

Frigidaire inherited the Electrolux code structure, which assigns a different letter to each appliance category. Knowing the letter tells you which appliance is talking before you look anything up, and the two digits after it narrow the fault to a circuit.

E-codes on laundry

E followed by two digits. The first digit names the system: E1 is filling, E2 is draining, E4 is the door, E5 is the motor control. E20 and E21 are the most common codes we see on Frigidaire front-load washers in Valdosta.

i-codes on dishwashers

A lowercase i followed by two digits. i10 is a fill failure, i20 and i40 are drain restrictions, and i30 means water has collected in the base pan and the leak sensor has tripped. An i30 dishwasher will keep running its drain pump until the leak is found.

F-codes on cooking

F followed by two digits. F10 is a runaway oven temperature, F11 is a stuck key on the membrane panel, and F30 or F31 is the oven sensor circuit open or shorted. F11 is a panel fault, not an oven fault, and it is often mistaken for one.

The same structure appears on Electrolux-badged appliances, because both badges share the control platform.

What do Frigidaire error codes mean?

The codes below cover the faults we are called out for most often in Valdosta. Read the code from the display before calling, because it usually decides which parts come on the van.

Code	Appliance	Meaning	Usual cause
E10 / E11	Washer	Fill failed or was too slow	Inlet valve or supply tap
E20 / E21	Washer	Water not draining	Debris trap or drain pump
E13	Washer	Leak detected	Boot, sump or hose
E41 / E42	Washer	Door not locked	Door lock assembly
E5E	Washer	Motor control fault	Motor control board
i10	Dishwasher	Water not entering	Inlet valve
i20 / i40	Dishwasher	Drain restricted	Filter or drain pump
i30	Dishwasher	Water in the base pan	Sump gasket or hose
F10	Range	Oven over temperature	Sensor or relay
F11	Range	Key stuck on the panel	Membrane keypad
F30 / F31	Range	Sensor open or shorted	Oven temperature sensor

Call 229-363-0182 with the code and the model number from the door frame.

What are the most common Frigidaire appliance faults?

Frigidaire failures concentrate in the drain path on laundry and dishwashers, and in the ice maker and defrost system on refrigerators.

Frigidaire refrigerator repair

Frigidaire side-by-side and French-door refrigerators fail at the ice maker, the water inlet valve and the defrost system. The ice maker is the single most common Frigidaire refrigerator complaint, and it fails independently of cooling, so a refrigerator with no ice is usually otherwise healthy. A compressor that hums and cuts out after a few seconds has a failed start relay.

Ice maker stopped
No water at the dispenser
Fresh food warm
Clicking then silence
Frost build-up

Frigidaire washer repair

Frigidaire front-load washers stop with E20 when the drain is blocked. The debris trap behind the lower panel is the first check. Affinity models add a second common failure at the door lock, reported as E41, where the machine fills but refuses to start the cycle because it cannot confirm the door is latched.

E20 drain error
E41 door fault
Will not spin
Loud on spin
Leaking underneath

Frigidaire dryer repair

Frigidaire dryers fail at the heating element, the thermal limiter and the drive belt. A Frigidaire dryer that runs cold has an open element or an open limiter, and the limiter opened because airflow was restricted. Replacing it without clearing the vent produces the same failure again within months.

No heat
Long drying times
Squealing on start
Will not start
Drum not turning

Frigidaire dishwasher repair

An i30 is the Frigidaire dishwasher fault we see most. Water has reached the leak sensor in the base pan, so the machine stops mid-cycle and runs the drain pump continuously. The leak is normally the sump gasket or a split hose. Drying the pan without locating the source only postpones the next shutdown.

i30 leak error
i20 drain error
Will not fill
Dishes still dirty
Will not start

Frigidaire range and oven repair

Frigidaire electric ranges fail at the bake element, the oven sensor and the membrane keypad. An F11 code is a stuck key rather than an oven problem: the panel believes a button is being held down, so the control refuses every other command. The oven itself is usually perfect on an F11.

F11 stuck key
Oven will not heat
Temperature drifting
Burner not working
Door locked shut

Frigidaire freezer repair

Frigidaire upright and chest freezers fail at the start relay, the defrost timer and the door gasket. A gasket that no longer seals draws humid Georgia air into the cabinet, which shows up as heavy frost and a compressor that never cycles off. That is a cheap repair that is frequently mistaken for a dying freezer.

Heavy frost
Running non-stop
Not freezing
Door not sealing
Alarm sounding

Where is the Frigidaire model number?

Frigidaire model numbers open with F, and the letters after it set the tier: FF is the standard line, FG is Gallery, FP is Professional.

Find the plate

Refrigerators: inside on the left wall or behind the crisper drawer. Washers and dryers: inside the door opening or on the rear panel. Dishwashers: on the door edge. Ranges: behind the storage drawer or on the oven door frame.

Note the tier

Gallery and Professional models carry more electronics than the standard line, so they have more boards available to fail. The tier also decides which control board fits, because the mechanical parts frequently carry across while the boards do not.

Call with the code

A Frigidaire code plus a model number is usually enough to identify the failed part before we arrive, which is why Frigidaire repairs tend to finish in a single visit.

Where do we repair Frigidaire appliances?

We cover Valdosta and the surrounding Lowndes County communities, plus nearby towns in Brooks, Lanier and Cook counties.

Valdosta
Remerton
Hahira
Lake Park
Dasher
Moody AFB
Quitman
Adel
Nashville
Ray City
Morven
Naylor

Frigidaire repair questions

Answers to what customers ask before booking a Frigidaire repair.

Is Frigidaire the same as Electrolux?

Frigidaire is owned by Electrolux and shares its control platform.

Electrolux acquired Frigidaire in 1986 and sells it as the mainstream North American badge, with Electrolux reserved for the premium tier. Many parts carry across the two, and both use the same fault code structure, which is why an Electrolux washer and a Frigidaire washer both report E20 for the same problem.

What does i30 mean on a Frigidaire dishwasher?

i30 means water has collected in the base pan and tripped the leak sensor.

The dishwasher stops and runs its drain pump continuously to protect your floor. The source is usually the sump gasket, a split hose or a loose connection at the pump. The sensor is doing its job, so the repair is finding and fixing the leak rather than resetting the code.

Why does my Frigidaire oven show F11 and beep constantly?

F11 means the control believes a button is stuck down.

The fault is in the membrane keypad rather than the oven. Because the control thinks a key is being held, it ignores every other command, which makes a working oven look completely dead. Cutting power at the breaker for five minutes sometimes clears it temporarily, but a recurring F11 needs the panel replaced.

Why does my Frigidaire washer keep showing E20?

E20 means the machine could not empty in the time allowed.

Check the debris trap behind the panel at the bottom front, with a shallow tray underneath to catch the water. Coins, hair clips and fabric are the usual finds. If the trap is clean and E20 returns, the drain pump or the hose is blocked further along.

Are Frigidaire appliances worth repairing?

Yes for mechanical faults, and it depends for board faults.

Frigidaire sits at a lower price point than most brands on this site, so the replacement cost is lower and the repair-or-replace line comes sooner. Pumps, valves, locks, elements and gaskets are inexpensive and always worth doing. A main control board on an older unit is the point where replacement starts to make more sense.

Why does my Frigidaire freezer frost up so quickly?

Humid air is getting in past the door gasket.

South Georgia humidity makes this worse than it would be further north. A gasket that has hardened or torn lets moist air in, which freezes on the coldest surface it reaches. Close the door on a sheet of paper and pull: if it slides out with no resistance, the gasket has lost its seal at that point.

Book a Frigidaire repair in Valdosta

Have your model number and any error code ready when you call.

229-363-0182

Appliance Repair Valdosta is an independent appliance repair company. We are not affiliated with, authorised by, or endorsed by Frigidaire or Electrolux. Brand names and model designations are used only to identify the appliances we service.